Top 10 common forklift mishaps ， forklift operation ought to take note of these matters ！.

Do not underestimate the forklift at the office. If the procedure is bad, there will be severe crashes in mins, and there are several crashes entailing forklifts.

Instance 1: The forklift freight obstructed the driver's sight, and the individual ahead can not be located, resulting in a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy products, the workers used their body weight as the counterweight, which almost created casualties.
Instance 3: The size of the forklift freight exceeds the allowable size of the course and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure need to pay attention to these issues ：.

Beginning.
1. Before beginning, observe the environments, and after verifying that there are no obstacles that impede the security of driving, beep the horn first and then begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the tons is secure and reputable.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, be careful that there will be no barriers overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be reduced to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it needs to follow the web traffic rules in the manufacturing facility and have to maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest placement that does not hinder the driving, and the gantry should be properly tilted back. The load shall not be elevated other than when piling or filling. .
8. The height of the lots have to not obstruct the motorist's view. In special situations, when the product affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive securely at a reduced speed when entering the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to base on the fork to hold products and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported Stand-on Electric Pallet Stacker in a timely manner, and they will certainly never operate with ailments or hide them.

packing and unloading.
1. When fork-loading things, the distance in between both forks ought to be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is forbidden to deal with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and Stand-on Electric Pallet Stacker it must be kept in mind that the fork suggestion need to not touch other items or objects. The tons needs to be stabilized with very little back tilt of the gantry so that the load does not move in reverse. The mast can be tilted onward slightly when the tons is decreased to allow for easy positioning of the lots and extraction of the forks. .
6. It is prohibited to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the emergency brake deal with to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and gas, lubricating oil and cooling water should be included.
2. Examine the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage should also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the gradient is above 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and move forward, if they run into big or hefty goods and most likely to the driver's line of vision, they should take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Car parking is not permitted under the list below problems.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844